Large print starts at 16 point. GOV.UK's guidance on accessible communication formats defines large print as a point size of 16 and above, and it recommends 16 point as the minimum. Set your body text to at least that size, then fix the layout that shifts around it.
This page shows how to set the size once in a word processor, what happens to the page count, and what to proofread before you hand out copies. For choosing a size in general, read what font size is easy to read.
What counts as large print
The guidance sets 16 point as the lowest size for a large-print copy. It adds that some fonts look larger than others at the same point size. One number never settles it.
It also says no single size suits everyone. If you make a copy for one reader, ask which size works for them. Think twice before going above 28 point. The guidance warns that very large type makes a document bulky and hard to find your way around.
| Size | What the sources say | What to do |
|---|---|---|
| 12 point | Suggested minimum for standard print | Not large print |
| 14 point | An option the guidance mentions for standard print | Still not large print |
| 16 point | Large print starts here | Use as the floor for a large-print copy |
| 18 point | WCAG calls 18 point text "large-scale" and lowers its contrast target from 4.5:1 to 3:1 | A step up when the page count allows |
| Above 28 point | The guidance asks you to consider requests with care | Check that the copy stays easy to handle |
Set the size once with styles
Change the style, not each paragraph. Microsoft's help page on styles says that all text using a style changes when you change the style. Menu names can differ by version, so look for the same words in yours.
- On the Home tab, right-click the style your body text uses and choose Modify.
- In the Formatting section, set the size to 16 or more.
- Choose whether the change applies to this document only or to new documents too.
- Repeat for Heading 1, Heading 2 and any caption style. Keep each heading larger than the body text.
Do this on a copy of the original file. Keep the standard version as it is. Then look at the gaps between lines. Larger type in tight lines looks cramped, so see line spacing for how much room to give.
Keep the layout clean as pages multiply
Bigger type means fewer words per line and more pages. Plan for that before you print.
Cut words before you cut size. The guidance says to reduce the amount of text before reducing the point size. Trim a paragraph rather than shrinking the type to fit a page. The Easy-Read Editor can help you spot long sentences that are worth cutting. Here is one example of such a trim.
Before: Attendees are kindly requested to make their way to the main hall for the commencement of the session.
After: Please go to the main hall. The session starts at ten.
Watch the line length. The same page asks for 50 to 65 characters per line, including spaces. It says fewer than 65 is better and no line should pass 80. Count the characters in a few lines. If they run long, widen the side margins. The article on column width goes deeper.
Keep headings with their text. The guidance asks you to proofread so that headings and paragraph text match the page breaks. In Word, select the heading, open the Paragraph dialog from the Home tab, go to Line and Page Breaks, and select Keep with next. Microsoft's help page lists this setting under Pagination.
Rebuild, do not enlarge. The guidance says not to make large print by enlarging a standard page on a photocopier. Change the size in the document instead, so lines and pages break in sensible places. For complex jobs with pictures, it suggests a commercial printer for consistent quality at larger sizes.
Proof the printed copy
Print one page and hold it at normal reading distance. Then work through this list.
- Body text is 16 point or larger.
- Headings are larger than body text and sit with the paragraph below them.
- Lines run between 50 and 65 characters.
- No heading is stranded at the bottom of a page.
- Page numbers are on every page, since the copy is now longer.
- The margins leave room to hold the page. See page margins.
- A last look at the whole printout with print preview shows no surprises.
Common mistakes
- Scaling at print time. Printing at 150 percent does not reflow the text. Lines can run off the page. Set the size in the document.
- Raising body text only. If headings stay small, they stop looking like headings.
- Ignoring the page count. A one-page notice can run to several pages. Decide what to cut before you print.
- Skipping the proofread. Page breaks move when the size changes. A heading can end up alone at the bottom.
- Going very large by default. The guidance asks for care above 28 point. Ask the reader which size works.
FAQ
Is 14 point large print?
No. The guidance defines large print as a point size of 16 and above. It mentions 14 point as an option for standard print.
Can I make large print by zooming in on the printer?
It is better not to. Scaling at print time keeps the layout and enlarges everything, so lines can run off the page. Change the size in the document and print at actual size.
Do all fonts look the same size at 16 point?
No. The guidance notes that some fonts appear larger than others at the same point size. Print a test page and check. The page on choosing a font helps with the pick.
How many pages will the copy have?
More than the standard copy. Change the size first, then count the pages. Do not guess.
Sources
Each page below was opened and read on the date shown. Where a fact comes from one of them, the guide says so.
- Accessible communication formats Checked November 19, 2026
- Customize or create new styles (Microsoft Support) Checked November 19, 2026
- Use Line and Page Breaks settings in Word (Microsoft Support) Checked November 19, 2026
- Understanding Success Criterion 1.4.3: Contrast (Minimum) Checked November 19, 2026
This guide gives general information about readability. See the Disclaimer. To report a mistake, use the Corrections page.